Question: Kawasaki Kg2900a Generator Parts

I Am Looking For Kawasaki Small Generator Parts.

I need the ignition coil, the condenser and the point set. for a kawasaki kg550a small gas generator. i have the factory part no#s but have had no luck finding parts on the internet. ...

I Have A Onan Emeral 4000 Watt Generator.will Not Run

I have a Onan Emeral 4000 watt generator. It only runs if I hold the start button, when I release it she stops. I have plenty of oil in it and I disconnect the oil pressure switch to see if this would help What else could cause the generator to run only when the start switch is held. The gen is on a 92 ford Tioga Does anyone know of any place i can order parts? Im leaning toward the main control ...

My Generator Can’t Keep Up With My Air Conditioner Marine Power Factor Cap

I have a little honda eu2000i generator which overload-protects at 13.3 amps. I have a Polar Bay 7000btu 120v/9amp (reported) air conditioner on my sailboat. The AC works great when plugged into shore power but the generator overload-protects within 10 seconds of the compressor kicking on. I'm pretty sure this is because of the power factor. How do I add a capacitor to the 120v line to help the generator stay online? Is there a better (more modular) way to solve ...

Do Electric Generators Charge The Battery Used To Start The Engine

The battery on my generator just went dead so I hooked the battery charger onto it. I'm not sure if the battery is fully charged yet. Will the generator charge the battery up the rest of the way if I have enough charge to get the engine started?? I didn't know if the generator worked similarly to a car charging the battery with the alternator. Thanks for your help!! ...

How Important Is The Major Maintenance On A Onan Generator Is Changing The Oil, Spark Plug And Filters Enough

The manual says the heads need to replaced or checked every 450 hours. It is worth paying $450 for a cummins tech to look at the generator? ...

Where To Find Obsolete Crankshaft And Con Rod Bearings

I have a '84 Kawasaki Voyager XIII (the 6 cylinder model) that I'm going to overhaul. Kawasaki no longer stocks bearings (as well as a number of other parts). Anyone know of anybody that manufacturers or stocks insert bearings (not ball or roller bearings) by dimension rather than brand and model? ...

Can I Use Sytntite Oil Instead Of SAE 40 For My Kawasaki 4 Stoke Air Cooled Vtwin

Want longer life. Have 23 hp kawasaki engine air cooled. ...

Kawasaki Bayou300 2000 Put New Shifter Rod In,how Does Spring Return For Shifter Get Connected

My question refers to part #92144,if u spread spring apart and put it around the tab above it the spring arm bends on a crankcase pin/stopper when shifting into gears.the diagram at kawasaki.com under parts diagram,gear change mechanism,doesnt show how the spring ends up.any ideas on how to find this out? what I realy need to know is where do Ifind a diagram of the finished product.What does the tention spring[92144]look like when it is all put back together.I think I need ...

What Would Make My Generator Light On The Speedometer Stay On

I have a 1973 VW Super Beetle that I just love. Its a project car. When I got the engine put in and started it, I noticed that the generator light on the speedometer will not go off. I did some reading and it said that I might need to change the voltage regulator. I changed the voltage regulator and it still stays on when the key is in the ignition. Any suggestions what it might ...

I Bought A 1999 Kawasaki ZXI 1100 Jet Ski, What Should I Do To Warm It Up

What kind of warm up procedure should I put my Kawasaki ZXI 1100 jet ski through when it has been sitting for long enough for the engine to cool down? It is a two stroke with oil injection. ...