Question: Briggs Plastic Crankshaft Gear With Two Timing Marks Marks

How To Set Ignition Timing 95 Honda Civic

I know how to use the light and how to adjust the distributor but how do i see the marks on the crankshaft pulley? Do I need to take the a/c and alternator belt off to see the marks. Also, Does the car need to be jacked up or can i just do this in the street. Thanks. I know how timing works and all, I just don't know how to see the marks while its operating. ...

Replacing Cam Gear On 1989 F150

Will I have timing problem? The "plastic" cam gear got eaten up by the hardened crank gear. They have marks on them, but I'm afraid that even with the marks th timing will be off? The Distributor does not turn obviously, but may be out of time when it broke? If so do I just retard or advance by distributor? Does the computer automatically time? Help! I will put in new parts this weekend ...

How Do I Set The Timing On A ’96 Prelude

I took the head to get worked on. I know that the crankshaft pulley has to be at 12:00. Are there marks on the distributor cap to make sure it's not 180 degrees off? When putting the camshafts back on the head, is just making sure the "Up" marks up, good enough? What's the firing order? Is it important? Do I have to make sure No. 1 piston is at TDC on the compression stroke? ...

What Is The Procedure For Setting Timing On 1994 Honda Accord 4 Cylinder

Rubber timing belt jumped a few teeth. Replaced with new belt but I need to know the procedure for setting the timing. Where do the marks on the cam gear and the crankshaft gear line up and on what stroke of the number 1 cylinder of the engine with the distributor rotor in what position. ...

Where Do The Timing Marks Go On The Cam Gears On A 1986 Toyota Corolla When Changing The Timing Belts

I'm about to replace a timing belt, not chain, on a 1986 toyota corolla. Its a 4 cylinder dual overhead cam. I need to know where timing marks on the cam gears go.... If anyone knows for sure I would appreciate your answer. ...

How Do I Set The Timing Gear On A Briggs And Stratton Single Cylinder Small Engine

I had to replace the connecting rod and the big plastic gear fell out of place before I could note the positions of the gears. How do I get them properly aligned? On the big plastic cam gear I do see a marking, but what do I align it with? I understand to align it with the crank gear. The plastic gear has a double mark, and on the crank gear there is a tiny recessed square set on ...

Chevy 350 Timing Issues

-------------------------------------------------------------------------------- ok so i know im going to sound like a real idiot here but here goes. I have a 94 k 1500 with the 350 i took it apart to do intake gaskets valve cover gaskets rebuild the tbi and i did an ignition module just for the sake of it. i went to the parts store with my buddy and he convinced me to do a timing chain it does have 160,XXX on it so i bought an aftermarked timing ...

Understanding Top Dead Center

Hey all, i just bought a 1990 Acura Legend V6 5 Speed Coupe, and it has a broken Water Pump so i will be replacing this as well as the timing belt while im in there. anyways, i understand most of the timing belt procedures but am a little confused with the Top Dead Center Portion.... 1. How am i supposed to line it up at top dead center? 2. Do the Cam Pulleys Line Up Together and the Crank Pulley Lines up ...

Still Looking For The Right Answer About My 2000 Kawasaki Prairie Timing

I started with a broken cam chain dowel pin on the sprocket, bent valves, stretched timing chain. Replaced with new parts, set everything by the manual,got it running but would pop back through the carb if you open up the throttle but would idle perfect high or low idle, but after running for a few minuets would get very hot so I checked my timing and it just will not line up with the timing marks exact that the manual says. ...

Problem With My 77 Chevy Truck, With 350 Crate Engine

The truck drives well appear at regular intervals in neutral. The main problem is when I give it gas it runs strong until about third Gear and then it's seams on the wall to beat the power will cease to accelerate it, he used to stall or die, just not speed. I have recently replaced the fuel pump. I'm thinking maybe timing advanced? The box to check engine timing marks do not, any ideas? Thanks. ...